If you want the short answer: the Turin DF64 Gen 2.7 ($354) is the one most people should buy. 64mm flat burrs and single dosing at a price nobody else matches, and it is the model we sell most of. Spend less and the DF54 V 4.1 ($225) does the same job with smaller burrs. Spend more and the DF83 Gen 2 ($499) gives you 83mm burrs for less than most brands charge for 64mm.
Everything below is the reasoning, starting with the table this article should always have had.
Turin grinder comparison table
| Grinder | Burrs | Price | Best for |
|---|---|---|---|
| H40 V2 | 40mm, hand crank | $49 | Travel, backup, camping |
| SK40 | 40mm steel | $199 | The cheapest way in |
| DF54 V 4.1 | 54mm flat | $225 | First serious espresso grinder |
| DF64 Gen 2.7 | 64mm flat | $354 | Most people. The benchmark. |
| DC63 Conical | 63mm conical, Red Titanium | $398 | Milk drinks, darker roasts |
| CF64V | 64mm flat, variable speed | $449 | DF64 plus speed control |
| DF83 Gen 2 | 83mm flat, Red Titanium | $499 | Straight espresso, light roasts |
| DF83V | 83mm flat, variable speed | $699 | As much grinder as a home needs |
Every grinder above except the H40 is single dosing: you weigh the beans in, grind them all out, and nothing sits in a hopper going stale. All of them use stepless adjustment, so you are not stuck between two settings that are both wrong.
Which one should you actually buy
If you are buying your first espresso grinder: the DF54 at $225. 54mm flat burrs is the point where a grinder becomes genuinely espresso-capable rather than espresso-tolerant.
If you want the one we recommend most: the DF64 at $354. It is the value benchmark in the whole category, not just Turin's range.
If you drink mostly milk drinks: the DC63 at $398. Conical burrs give a rounder, heavier cup — which is what you want under milk, where the flavour separation that flat burrs buy you is largely covered up anyway.
If you drink straight espresso and buy light roasts: the DF83 at $499. 83mm burrs and the uniformity that comes with them is what gets clarity out of a bright coffee.
If you want one grinder to last a decade: the DF83V at $699. This is the ceiling for a home setup and there is very little above it that you would hear.
If you need something for travel: the H40 hand grinder at $49.
The lineup
Turin SK40 — $199
40mm hardened steel burrs, single dosing, stepless adjustment, and the smallest footprint in the range. This is the cheapest grinder we would put in front of an espresso machine.
It will pull espresso, and stepless adjustment at this price is genuinely unusual — most $199 grinders are stepped, which means you are choosing between a shot that gushes and one that chokes. What you give up with 40mm burrs is speed and a little consistency. If espresso is your main drink and you can find another $26, the DF54 is the better buy.
Turin DF54 V 4.1 — $225
54mm flat burrs and single dosing for the price of a basic hopper grinder. The V 4.1 revision is the current one.
This is where the range gets properly good. 54mm flat burrs produce a tight enough particle distribution that you can taste what you changed when you adjust the grind — which is the whole point, and the thing cheaper grinders cannot do.
Turin DF64 Gen 2.7 — $354
64mm flat burrs, single dosing, stepless adjustment. The one we sell most of, and the one we recommend most often.
64mm is the sweet spot for a home grinder. Going from 54mm to 64mm is a change you will taste. Going from 64mm to 83mm is a change you will taste on light roasts pulled carefully, and not much otherwise. The DF64 sits exactly where the returns stop being obvious, which is why it has become the default recommendation across the whole category rather than just ours.
It is also the most upgradeable grinder in the range — see the burr section below.
Turin DC63 Conical — $398
63mm Red Titanium conical burrs, single dosing, stepless adjustment with a large dial.
The only conical grinder Turin makes, and it exists for a real reason rather than as a variant. Conical burrs crush between a cone and a ring rather than shearing between two discs, and the slightly wider particle distribution that produces reads in the cup as body. The shot is rounder and heavier.
Under milk that is an advantage rather than a compromise. If you drink cappuccinos and flat whites and buy medium-to-dark roasts, this is a better grinder for you than the DF64 at a similar price. Conicals also run quieter and cooler.
Turin CF64V Variable Speed — $449
64mm flat burrs with variable speed control and stepless adjustment.
The DF64 with a speed dial. See the section below on what that actually buys you — the short version is that slowing the burrs down generates less heat and slightly tightens the grind, which matters most on light roasts and matters very little on a dark roast going under milk.
Turin DF83 Gen 2 — $499
83mm Red Titanium coated flat burrs, single dosing, stepless adjustment.
83mm burrs at $499 is the single most aggressive piece of pricing in the whole grinder market. Most brands want $900 and up for burrs this size. Bigger burrs grind faster and generate less heat doing it, which is why they hold a more consistent particle size — and uniformity is exactly what you taste in a straight shot with nothing to hide behind.
If you drink espresso black and you buy light roasts, this is the one.
Turin DF83V Variable Speed — $699
83mm flat burrs plus variable speed. The top of the home range.
This is as much grinder as most homes will ever need, and we say that as the people who would profit from telling you otherwise. Above this you are into commercial machines that are louder, larger and built for a queue rather than a morning.
Also in the range
The H40 V2 hand grinder ($49) for travel, and the ZF83 Commercial ($1,400) if you are running a café rather than a kitchen. The DF64V Gen 3 ($499) adds an ion generator to reduce static clumping on top of variable speed; it is currently out of stock, so call if you want one and we will tell you when it lands.
What variable speed actually does
Three grinders in the range have it, and the marketing around it is vaguer than it needs to be.
Slowing the burrs down does two things. It generates less heat, which matters because heat drives off aromatics as you grind. And it slightly tightens the particle distribution, because beans spend marginally longer being cut rather than being thrown through.
The honest assessment: it is a real effect and it is a small one. You will notice it on a light roast pulled carefully and evaluated black. You will not notice it in a cappuccino. If you are choosing between the DF83 at $499 and the DF83V at $699, ask yourself what you actually drink before you spend the extra $200.
Burr upgrades, which nobody writes about
This is the part of the Turin range that gets overlooked, and it is the reason the DF64 and DF83 are better long-term buys than their price suggests: the burrs come out and better ones go in.
SSP burrs are made by a Korean manufacturer that supplies a lot of the high-end grinder world, and they are the single biggest upgrade available to either grinder.
- DF64 SSP Unimodal (Multi Purpose) — $185
- DF83 SSP High Uniformity — $325
- DF83 SSP Unimodal MP — $325
High Uniformity burrs push toward clarity and separation. Unimodal Multi Purpose burrs are the more forgiving choice and handle filter as well as espresso.
DLC coated burrs are a cheaper step: a diamond-like carbon coating that stays sharper for longer and shifts the grind slightly.
- DF83 DLC Espresso — $99
- DF83 DLC Brew — $99
What this means practically: a DF64 at $354 plus SSP burrs at $185 is $539 total and competes with grinders costing twice that. It also means you can buy the grinder now and upgrade it in a year rather than replacing it.
Call 800-410-8867 before you order burrs. Which set is right depends on what you drink, and the wrong one is an expensive way to make your coffee worse.
To summarize
Turin currently offers grinders in all price ranges with different features and burr sizes ranging from 40mm to 83mm.
- Cheapest way in — Turin SK40, $199
- Best value — Turin DF54, $225
- Most popular — Turin DF64, $354
- Best for milk drinks — Turin DC63 Conical, $398
- Most consistent — Turin DF83, $499
- Customizable — Turin CF64V or Turin DF83V
Not sure? Our grinder matcher asks four questions and names one, and it will point you at the cheaper grinder when the cheaper grinder is right.
Turin Grinders FAQ
1. What makes Turin coffee grinders unique?
Turin grinders are known for their high-quality build, precision grinding, and affordability. They cater to a wide range of brewing methods and feature innovative designs like low retention and stepless adjustments.
2. Which Turin grinder is best for espresso?
The DF64 Gen 2.7 is the best all-round choice for espresso. If you drink it black and buy light roasts, the DF83 Gen 2 and DF83V give you larger burrs and more uniformity. If you mostly drink milk drinks, the DC63 Conical suits you better than any of them.
3. What is single-dose grinding, and why is it important?
Single-dose grinding minimizes coffee retention, ensuring each grind is fresh and consistent. Many Turin grinders, like the DF64 and DF64V, are designed for single-dose use, making them ideal for preserving coffee flavor.
4. Are Turin grinders easy to clean?
Yes, Turin grinders are designed for easy cleaning. Many models feature accessible burrs and low retention, reducing the buildup of stale coffee grounds.
5. Can Turin grinders handle multiple brewing methods?
Absolutely! With stepless grind adjustments, Turin grinders can be calibrated for a variety of brewing methods, from espresso to French press.
6. What is the difference between the DF64 and DF64V?
The DF64V adds variable speed control to the popular DF64, allowing for more precise customization of grind speed, which can enhance flavor extraction for different brewing methods.
7. Is the Turin SK40 suitable for espresso?
Yes. Its 40mm burrs and stepless adjustment will pull espresso, and stepless adjustment at $199 is rare. The trade is speed and a little consistency against the larger burrs — so if espresso is your main drink, the DF54 at $225 is the better buy for very little more.
8. Are replacement parts available for Turin grinders?
Yes, replacement burrs and other components are widely available, ensuring long-term use and maintenance of your Turin grinder. We stock SSP and DLC coated burr upgrades for both the DF64 and the DF83.
9. Do Turin grinders come with a warranty?
Most Turin grinders come with a manufacturer's warranty. Be sure to check the specific warranty details when purchasing from your retailer.
10. Where are Turin grinders manufactured?
Turin grinders are manufactured in China by well-regarded companies specializing in coffee equipment, ensuring a balance of quality and cost-effectiveness.
The short answer
The DF64 Gen 2.7 at $354 is the right grinder for most people. Go down to the DF54 if the budget is tight, sideways to the DC63 if you drink milk drinks, up to the DF83 if you drink espresso black. Variable speed is real but small, and burr upgrades will take any of them further than a more expensive grinder would.
Call 800-410-8867 and tell us what you drink. We would rather talk you into the cheaper right grinder than the more interesting wrong one.
